11 Civil Engineering Quiz | Estimating Cost MCQ
1 >>The concrete work for the following part of the building of specified thickness is measured in square metres
 ?- (A) Wall panels
- (B) Floors
- (C) D.P.C
- (D) all
- (A) Length, breadth, height
- (B) Height, breadth, length
- (C) Breadth, length, height
- (D) None of these.
- (A) The mica flap valve which opens inwards only, is fitted at the top of the inlet pipe
- (B) The water seal is less than that of ordinary traps.
- (C) The height of fresh air inlet pipe fixed vertically with wall is 3 m
- (D) It is provided a cleaning eye at the top of the trap
4 >>Pick up the item of work not included in the plinth area estimate
 ?
- (A) Verandah area
- (B) W.C. area
- (C) Courtyard area.
- (D) Room area
- (A) The formal acceptance by the administrative department for incurring an expenditure on the work, is called administrative approval
- (B) The actual expenditure involved to complete a work including incidental, establishment and travelling charges, is called actual cost
- (C) The order of a competent authority sanctioning a properly detailed estimate of the cost of a work of construction or repair is called technical sanction
- (D) all
- (A) 1.5 m3
- (B) 3.5 m3
- (C) 5.0 m3
- (D) 2.5 m3
- (A) D/3 [first area + last area + 2∑ Even area + 4 ∑ odd areas]
- (B) D [first area + last area + ∑ Even area + 2 ∑ odd areas]
- (C) D/3 [first area + last area + 4∑ Even area + 2 ∑ odd areas]
- (D) D/6 [first area + last area + 2∑ Even area + 4 ∑ odd areas]
- (A) 26, 000 m3
- (B) 27, 000 m3
- (C) 26, 500 m3
- (D) 27, 500 m3
9 >>The brick work is measured in sq metre, in case of
 ?
- (A) Half brick walls or the partition
- (B) Honey comb brick work
- (C) Brick flat soling
- (D) all
- (A) In laying pipes, the method of jointing and fixing is specifically specified
- (B) Cutting through walls and floors are included with the item
- (C) Pipes are classified according to their sizes and quality
- (D) all
- (A) Connection to drains
- (B) Bed concreting
- (C) Setting and laying
- (D) all
- (A) The bent up bars at a support resist the sharing force
- (B) The bent up bars at a support resist the negative bending moment
- (C) The bending of bars near supports is generally at 45°
- (D) all
- (A) Ordinary cuttings up to 1 m
- (B) Surface excavation up to 30 cm depths
- (C) both surface dressing up to 15 cm depths and Surface excavation up to 30 cm depths
- (D) surface dressing up to 15 cm depths
- (A) Volume should be measured correct to O.Olcum
- (B) Dimension should be measured correct to 0.01 m
- (C) Area should be measured correct to 0.01 sqm
- (D) all
15 >>Brick walls are measured in sq. m if the thickness of the wall is
 ?
- (A) 15 cm
- (B) 20 cm
- (C) 10 cm
- (D) None of these.
- (A) 1.35 for 20 users
- (B) 1.80 litres for 5 to 10 users
- (C) 1.20 litres for 15 users
- (D) all
- (A) breadth of the wall
- (B) one fourth breadth of wall on each side
- (C) half breadth of wall on each side
- (D) None of these.
- (A) 70cm
- (B) 80cm
- (C) 75cm to 80cm
- (D) 60cm
- (A) The bent up bars at a support resist the sharing force
- (B) The bent up bars at a support resist the negative bending moment
- (C) The bending of bars near supports is generally at 45°
- (D) all
- (A) 10 sqm
- (B) 2.5 sqm
- (C) 5.0 sqm
- (D) 7.5 sqm
